Usually, severe storms leave trails of visible destruction in their paths. From hail-damaged rooftops to broken windows, storm damage usually requires quick repairs and makes up approximately 11 percent of homeowners insurance claims in the United States. Fortunately, it’s generally easy to tell which areas of your home need help after a strong storm blows through. But what if severe weather comes and goes without leaving obvious signs of damage behind? Here are some sneaky indicators that your home requires storm restoration Minneapolis services, even if the damage isn’t visible to the untrained eye.
Dented Flashing and Gutters
If you have bald spots on your roof where your shingles have blown completely off, it’s pretty obvious you need storm repair services. However, dented flashing and gutters are less obvious indications of roof damage and are easy to overlook. If left unchecked, dented gutters and/or loose fittings could become major issues down the road. After a storm, check your flashing and gutters carefully to make sure they’re properly attached and in good working order. You may be able to prevent excessive storm damage to your gutters by cleaning them out and cutting down any dead tree limbs that could fall on them before a storm hits your area.
Minor Leaks Indicators
Hail, excessive wind and heavy rains can cause minor leaks in your roof. That can go undetected if you aren’t specifically looking for them. Leaks can cost a lot of money if you don’t notice and fix them when they are still minor. Sneaky signs of a leaky roof include one or more water stains on your ceiling, unexplained spots on your exterior walls or the smell of mold in your home. You may need to climb into your attic. Carefully observe your roof from the outside to determine if and where water is seeping through.
If you notice these common signs of hidden storm damage, don’t procrastinate fixing them. It’s wise to have the damage repaired as quickly as possible to avoid costly repairs down the road.…
People tend to take their roofs for granted. You rarely think about it until something goes wrong. Remember, your roof takes the brunt of the elements. Not only does it protect you and the inside of your home from rain and snow, but the sun also beats down on it every day, wearing it away. Over time, the roof becomes dried, cracked and worn. Now might be a good time to grab a ladder and see just how healthy your roof is.
When a Roofs Gives Out
Few things can be more devastating to a home than a roof collapse. Not only is your roof shot, but the underlying structure and everything below is likely to be destroyed as well. You could be looking at thousands of dollars in damage. Having a roof cave in must be avoided at all costs. Fortunately, there are measures that can be taken.
Taking Precautions With a Roof
If you want to get the most life possible out of your roof, there are certain steps you can take. Make sure shingles are replaced and holes are mended. A leak, especially in the winter, means something isn’t right. The quicker you find the source, the better.
When Snow Gets You Down
Snow gets many people down. Don’t let it get your roof down, too. You shovel and plow your walks and driveway. By the time that’s over, it’s easy to forget what’s right over your head. You may not realize how much weight your roof can or cannot support. Many times, the snow that weighs a lot doesn’t look like a lot. Heavy wet snow can be fatal to a roof. Coupled with rain, sleet and ice build-up, you’ve got a recipe for disaster.
Keeping Your Family and Home Protected
Letting your roof go could be a costly mistake. The good news is that these problems can be easily prevented if you know how. Taking care of your roof starting now can give it many more years of life to come.…
Signs Your Chimney Needs to Be Cleaned
On colder winter nights, there’s nothing quite like a fire roaring the hearth. If you use your fireplace regularly, however, you need to perform the proper maintenance. When chimneys aren’t cleaned, buildups of soot and creosote develop, which can have dangerous consequences. Here are a few signs that your chimney needs to be cleaned.
Creosote is the main reason why chimney users need to perform regular maintenance on their chimneys. Most experts recommend that homeowners clean their chimneys at least once a year. These cleaning sessions are primarily to get rid of creosote buildup. Creosote is the result of incompletely burned wood; when you light a fire without sufficient oxygen, it results in unburned tar vapors, which collect over time. If the layers of creosote get too thick, it can cause chimney fires.
To avoid this fate, homeowners should know how to detect creosote buildup. First, they should check for downdrafts coming from the chimney. If the airflow is coming down the chimney, open windows and doors until the flow of air reverses. Once the air is moving in the right direction, put on a pair of goggles, grab a poker, and strike the creosote deposits above the smoke chamber. Ideally, the poker should leave a thin mark on the wall. If the scratch has the depth of a paper cut, your chimney doesn’t need to be cleaned. If the scratch has a measurable width, like 1/8-inches to 1/4-inches, your chimney needs to be cleaned before you use it again.
Other Signs That Your Chimney Needs to Be Cleaned
A visual inspection of creosote buildup isn’t the only sign of a chimney in need of a sweep. When using the fireplace, homeowners should be on the lookout for unusual activities, like slow-starting fires and smoke that fills the room or house. When the fire isn’t burning, homeowners may notice strange smells or gusts of cold air.
Don’t let your fireplace turn into a safety hazard. If your chimney needs professional assistance, look for expert chimney cleaning Washington DC.…
The ceiling fans have always served the mankind by providing all the ventilation necessary for a room. The ceiling fans circulate the air in a room which is highly vital for the freshness factor to be maintained in a room. Whatsoever might a product be, equipped with all the advancements in technology and with features more than that of ceiling fans like air conditioning and heating facilities, it can now way substitute a fan. A fan has become an indispensable electrical furnishing for every home and does its bit by providing relief and comfort to the people. May it be the winters or the scorching heat in the summers, a ceiling fan gives relief in both the seasons by spreading the cold air pockets in the chilly days and bringing in the cool breeze from outdoors during the summers.
LATEST MODIFICATIONS IN THE CEILING FANS
As time has passed, man has been continuously trying to modify all the existing facilities that would result ultimately in better outputs. The ceiling fans have also gone a series of modifications and feature additions in the due course and the ceiling fans that we see today are a result of such evolution. The latest features that have been added to the ceiling fans include bladeless design, remote controlled power toggling option, LED lighting system etc. Off all such developments, the LED lighting system when equipped on the fans possesses a great advantage for the people. People generally have separate arrangements for the fans and lighting systems in their houses. Now if fans come with attached and easy to control LED lights, the additional costs for the lighting system can be effectively curtailed resulting ultimately in lesser investments
THE LED CEILING FANS ADVANTAGES
Luminous Luminaire (80 Watts), Orient Spectra, Havells Leganza, Crompton Greaves Uranus are some of the best fan models with LED lighting system. The LED lighting system on these fans , which is specifically designed for saving up some additional energy and eliminate the need of a additional lighting system, also adds to the style quotient of the house. The fans with LED lighting look trendy and are easy to operate as well. Most of the LED lighting systems that are mounted on the fans are operated using a remote (Orient Spectra). However an additional wire is sometimes provided along the fan connection so that the light can be operated using the wall mounted switches. A variety of fans are available in the market basing upon the power of the LED lights and features of the fan itself. A customer can easily choose from a wide range of options basing upon his needs.
WHERE TO GRAB THE BEST CEILING FANS WITH LED LIGHTS?
Almost every fan company has now come up with fan models that have LED lighting system. The additional advantages that such fans have to offer owe to their pricing on a bit higher side. However one can get huge discounts by checking the above listed fan models available on several ecommerce sites like Flipkart, Amazon, eBay etc. One can also visit any retail stores to get the desired model of the fan with LED lights. Generally the lighting system is of 12 Watts of 18 Watts.
The fans have also a provision of dimming out the light if necessary by using a dimmer which is similar to the one which is used to control the speed of the fans. This means that these lights can double up as a bed time light too. The fans with LED lighting have shown a substantial rise in sales in the past few years.…
These days coloring the concrete surfaces both old and new using acid stains (also called reactive stain or chemical stain) is very popular because of its unique looks and cost effectiveness. Acid staining is a process in which an aqueous solution of metallic oxides and inorganic acid is sprayed over an existing concrete surface. The acidic solution of metallic oxide reacts with lime (Calcium Hydroxide) present in the concrete yielding insoluble, colored compounds that become a permanent part of the concrete. Therefore, one of the basic conditions where coloring concrete using acid stains is going to work is the presence of lime in the concrete. Quiet often people who have just bought a home or condo, remove the carpeting or vinyl tile, and find something underneath which they believe is concrete. When they spray the acid stain or reactive stain and wait to get disappointed because they do not see any change in the color on their concrete surface. This is because the substrate that looks like concrete is in fact gypsum based ‘Gypcrete’. Builders often use this on upper floors to level out areas of sub flooring and provide a good base for other types of floor coverings. Unfortunately, staining Gypcrete does not produce any desirable results since it does not contain any lime; moreover it is too soft and easily abraded. Therefore ‘Gypcrete’ cannot be used as a wear layer.
Since Gypcrete surfaces cannot be used as a wear layer and acid stains do not work on them, it is usual practice to apply a 1/16inch polymer modified concrete resurfacing material (also called micro-topping or skim coat). Please find below the steps involved in resurfacing Gypcrete and acid staining with a micro-topping or skim coat –
a. Sweep the Gypcrete surface and dry vacuum the surface thoroughly. Rake out the joints where drywall meets the floor. Clean the adjoining areas even those not being resurfaced with a micro-topping.
b. Install masking paper (plastic) at least 48″ high on the surrounding walls. Spray a light mist of water just to damp the surface (DO NOT FLOOD!)
c. Using a brand new rayon mop, apply the first coat of acrylic primer (Cp1000) after diluting it with water @ 1:1 ratio. After waiting for at least 60 minutes, apply second coat of diluted acrylic primer and let it cure overnight (or 10 hours at least) before proceeding to the next step.
d. Apply another coat of acrylic primer, this time non-diluted and let it dry for 30-60 minutes. The third coat of primer can be applied using garden sprayer (i.e., available in Home Depot or Lowes).
e. Apply a thin coat (1/16″) coat of micro-topping or polymer modified overlay using magic trowel. Please follow the link for specific instruction on application of polymer modified micro-topping, Sgraffino. Allow the micro-topping to cure for at least 24 hours. In damp and cold conditions (basements), wait for at least 48 hours before proceeding to the next step.
f. Apply acid stain on the completely dried micro-topping. Please follow the link for specific instruction on application of an acid stain, Patinaetch. Allow the acid stained surface to dry for at least 24 hours before proceeding to the next step.
g. The micro-topping needs to be protected with a good quality sealer. Apply one coat of water based epoxy sealer, Perdüre E32 followed be another coat of water based polyurethane, Perdüre U46. Allow at least 6 hours between the application of epoxy primer and polyurethane topcoat. The sealed surface will be ready for use after 24hours. Of course, it takes at least 3 days for full cure.
Making a mind for installing a floor in your house? Do not get confused; simple and durable flooring you can opt for is there. Vinyl flooring is one of the finest choices keeping in view the long lasting quality and its affordability. Especially when you are considering flooring of bathrooms and kitchen, vinyl floor is the best option. Trend of installing vinyl floor is increasing day by day. Not only the durability and affordability is the major reason but also it has a wide range to select from. There are various designs, colors and types and the prices depend on the quality and material used in manufacturing. Let’s discuss in detail the characteristics of this flooring.
Introduction To Vinyl Floor:
Vinyl floor is basically a building material made of polyvinyl chloride called PVC. It is made of engineered products instead of original material. Similar to linoleum but is more durable. It can be used in commercial areas like offices, shopping malls as well as in residential areas like bedrooms as well as kitchens and bathrooms.
Types Of Vinyl Floor:
There are basically two types of this flooring. One is called printed vinyl and the other is inlaid vinyl. Printed contains a thin sheet of vinyl and has a coating of printed-paper. It is cheap in cost and is not much durable, while the inlaid vinyl is thicker in sheet strength and is expensive. Both are available in the market in form of sheets as well as tiles.
Advantages Of Vinyl Floor:
Vinyl is less cost, long lasting and easy to maintain flooring. It is highly resistant to moisture and this quality makes it best option for the bathrooms and kitchen flooring. It can be the great flooring for heavy traffic areas like offices, shopping centers and schools. It’s underlay gives comfort to the foot and add insulation.
Disadvantages Of Vinyl Floor:
One of the major drawbacks of vinyl floor is that it cannot be refinished or polished. Over time when it looses its luster it looks dull and it can wear down. Though it is less in cost from other flooring but have short life comparatively. It is also sensitive to sunlight and cold and can get fade or crack.
When choosing for vinyl floors consider installation, cost and type of vinyl. Use inlaid vinyl flooring for heavy traffic areas like shopping centers, offices and schools. Printed vinyl floor is best for low traffic areas like personal bedroom. Use tiles if you want more designs and it is also easy to install on your own. But if you have tight budget go for vinyl sheets, as it is less in cost than tiles.
When you go shopping for an iron umbrella stand it is helpful if you know what kind of style you would like. There are so many on the market and they verge from the cheap and cheerful mass produced cast iron versions right through to the antique wrought iron ones made in the Victorian age.
Wrought iron pieces were once the sign of wealth and were very popular in the gardens and mansions of the elite. Talented blacksmiths spent weeks hand crafting these pieces and working with the iron until they had achieved a beautiful result. You can find some of these fantastic pieces at real bargain prices as often they have not been looked after. Covered in rust, they can look like too much work to bring back to their natural beauty. Often people will decide to buy a new iron umbrella stand rather than the antique.
But it doesn’t actually take that much work. You simply need a drill with the wire brush attachment, some sandpaper, a smaller hand held wire brush and a lot of patience. When you have taken the initial rust off you will need some primer, a rust inhibitor and finally some paint. You begin by removing the rust which you can do with the drill so long as you take things very slowly. You will need to use the sandpaper and hand held brush on the more intricate engravings. Once you have removed the rust and have achieved a smooth surface you will need to paint the piece with a rust inhibitor. An iron umbrella stand does attract rust as you tend to either use it outdoors or place wet umbrellas in it so protecting it in this way is very important. Then just prime the piece and apply a coat of paint and you will own a beautiful object.